Product ID:816 HIGH-NICKEL AND NICKEL BASE ALLOYS
MSDS Date:06/08/1990
FSC:3439
NIIN:00F030085
MSDS Number: BRXVP

ARCOS ALLOYS

1 ARCOS DR
MT CARMEL, PA 17851-0308
US

Emergency Phone: 717-339-5200

Info Phone: 717-339-5200

Cage: GO252

ARCOS ALLOYS DIV OF HOSKINS MFG CO

308 MTCARMEL, PA 17851 US

Telephone: 717-339-5200, CHEMTREC 800-424-9300

Cage: 03805

IRON

CAS: 7439-89-6

RTECS: NO4565500

Fraction By Weight: 2.5% %

CHROMIUM METAL, CHROMIUM, CHROME (SUSPECTED A1 HUMAN

CAS: 7440-47-3

RTECS: GB4200000

Fraction By Weight: 0.01-13%

OSHA PEL 1 MG/CUM (CEILING)

ACGIH TLV: 0.5 MG/CUM

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB

COPPER (DUST & MIST), BRONZE POWDER

CAS: 7440-50-8

RTECS: GL5325000

Fraction By Weight: BALANCE

OSHA PEL 0.1 MG(CU)/M3 (FUME)

ACGIH TLV: 0.2 MG/M3 (FUME)

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

MANGANESE, MN COMPOUNDS

CAS: 7439-96-5

RTECS: OO9275000

Fraction By Weight: 4%

OSHA PEL (C) 5 MG/M3 DUST

ACGIH TLV: 5 MG/M3 DUST 9293

NICKEL (SOLUBLE) (SUSPECTED HUMAN CARCINOGEN BY NTP, IARC,

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: 69%

OSHA PEL 1 MG/CUM

ACGIH TLV: 0.05 MG/CUM IC

TITANIUM (DRY POWDER) (TI)

CAS: 7440-32-6

RTECS: XR1700000

Fraction By Weight: 2.25%

Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:PRODUCT AS SUPPLIED PRESENTS NO HEALTH
HAZARDS. DUSTS, FUMES, & GASES CAN BE DANGEROUS TO YOUR HEALTH.
CHRONIC EXPOSURE DURING WELDING: LUNG DAMAGE, NEUROLOGICAL DAMAGE,
LUNG FIBROSIS, & OTHER LUNG DI SEASES. ELECTRIC ARC WELDING RAYS
CAN INJURE EYES & BURN SKIN.
Explanation of Carcinogenicity:SEE INGREDIENTS
Effects of Overexposure:INHALATION: DIZZINESS, NAUSEA, FEVER, DRYNESS,
WATERY EYES, HEADACHE, BREATHING DIFFICULTY, FREQUENT COUGHING,
CHEST PAINS, & EVEN PULMONARY EDEMA, ASPHYXIATION, & DEATH.

First Aid:INHALATION: REMOVE TO FRESH AIR. IF BREATHING IS DIFFICULT,
ADMINISTER OXYGEN. IF BREATHING STOPS, BEGIN ARTIFICIAL
RESPIRATION. SKIN: WASH W/SOAP & WATER. EYES: FLUSH W/WATER FOR AT
LEAST 15 MINS. IN GESTION: OBTAIN MEDICAL ATTENTION IN ALL CASES.

Flash Point:NON-FLAMMABLE
Unusual Fire/Explosion Hazard:ARCS, SPARKS & MOLTEN METALS CAN IGNITE
FLAMMABLES & COMBUSTIBLES OR CAUSE EXPLOSION.

Spill Release Procedures:CLEAN UP ANY GRINDING DUST OR WASTE RESIDUES &
PLACE IN DOT APPROVED CONTAINERS.

Other Precautions:AVOID INHALATION & SKIN EXPOSURE. DON'T EXPOSE SKIN
TO RADIATION WHEN HOT CUTTING OR WELDING.

Respiratory Protection:USE NIOSH APPROVED WELD FUME RESPIRATOR OR
AIR-SUPPLIED RESPIRATOR WHEN CUTTING, GRINDING OR WELDING IN
CONFINED SPACES OR WHERE LOCAL EXHAUST OR GENERAL VENTILATION DOES
NOT KEEP EXPOSURE BELOW RECOM MENDED TLV LIMITS.
Ventilation:LOCAL EXHAUST OR GENERAL TO KEEP EXPOSURE BELOW TLV LIMITS
Protective Gloves:RECOMMENDED
Eye Protection:GOGGLES, GLASSES, HELMET W/FILTER LENS
Other Protective Equipment:FACESHIELD, FLAME RETARDANT CLOTHING,
PROVIDE PROTECTIVE SCREENS TO SHIELD OTHERS
Supplemental Safety and Health

Appearance and Odor:SOLID WIRE

Stability Indicator/Materials to Avoid:YES
Hazardous Decomposition Products:GASES & FUMES FROM INGREDIENTS LISTED

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE W/LOCAL, STATE, &
FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.